| Certification: | ISO9001:2008 |
|---|---|
| Tooth Form: | Alternate Tooth |
| Diameter: | 80mm |
|
Still deciding? Get samples of US$ 28/Meter
Order Sample
|
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make on Made-in-China.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| High quality Carbide Tipped band saw blades list | ||
| Specifications | Teeth Form | |
| 27mmx0.9 | 1x.035 | 3/4 2/3 |
| 34mmx1.1 | 1-1/4x.042 | 3/4 2/3 |
| 41mmx1.3 | 1-1/2x.050 | 3/4 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.25 |
| 54mmx1.6 | 2x.063 | 3/4 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.25 |
| 67mmx1.6 | 2-5/8x.063 | 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.25 |
| 80mmx1.6 | 3x.063 | 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.25 |
| (C) | (Si) | (Mn) | (P) | (S) | (Cr) | (Mo) | (V) | (W) | (Co) | |
| cemented carbide | Co:10% Residual refractory metal carbides:Wc,Tic,Nbc,Tac,Vc | |||||||||
| HGS40 | 0.40 | 0.30 | 0.45 | 0.015 | 0.005 | 3.00 | 1.50 | 0.25 | ||
| project | cutting elements | band broking | sawing deviation | sawtooth crack | surface rough | sawtooth wear too fast |
| Adjusting the sawing machine | two guide rods should be located close to the workpiece guide block is wearing parts, must be regularly checked and timely replaced. | The broken belt guide block is worn or the adjustment distance is too large | The broken belt guide block is worn or the guide rod is loosening or shaking | |||
| Adjust the driven pulley to achieve the smooth operation of saw blade without dropping, stringing and biting the stop of the pulley. | the belt wheel is badly worn | |||||
| The iron brush used to remove sawdust is a vulnerable part. It should be checked and replaced in time. | The iron brush is damaged, and the saw belt groove is blocked by cutting debris | The iron brush is damaged and cannot work properly | ||||
| Adjust the driven pulley to have proper tension. For the saw belt used for a long time, the tension should be compensated and correctly matched with the concentration of cutting fluid (coolant). | saw belt tension too high | saw belt tension too low | ||||
| Correctly mix the cutting fluid (coolant) concentration | too low cutting fluid (coolant) or too low coolant concentration | |||||
| cutting parameters | Correct selection of saw band linear speed | saw band linear speed too low | saw band linear speed too low | saw band linear speed too low | ||
| correctly Choose saw feed line rate | saw band feed ratetoo large | saw band feed ratetoo large | saw band feed ratetoo large | saw band feed ratetoo large | saw band feed rate too large or too small | |
| Band saw blade selection | according to the characteristics of the workpiece to be cut, the tooth shape and the specification of the saw band are correctly selected | tooth saws too smal | tooth saws too smal | tooth saws too smal | tooth saws too smal | tooth saws too smal |
| and the new saw band is used, the initial running-in is needed, the parameters are gradually increased from low speed and slow feed, For maximum service life | band saws no running or running time short | band saws no running or running time short | ||||
| Do not forcibly use Saw bands that have exceeded their service life | sawtooth worn and scrapped | sawtooth worn and scrapped | ||||
| According to the characteristics of the workpiece to be cut, correctly select the tooth hardness | tooth hardness Over smal | tooth hardness over small | tooth hardness over small | |||
| The cut artefact | Observe the working surface for defects and inclusion of sand | sand or rust Poor workpiece surface, | ||||
| to cut into a bunch of workpiece, ensure correct clamping method | the workpiece moves during cutting process |
A corner of the workshop:
){kind=link}